Goulds Water Technology Turbine Pump Catalog

Turbine Catalog

GENERAL INFORMATION

  • TTO :  DIRECTORY FOR DISTRIBUTORS – VERTICAL TURBINE PRODUCT
  • BTURBINE :   LINESHAFT AND SUBMERSIBLE TURBINE PUMPS

TURBINE TERMS & CONDITIONS

  • STCTURBINE :  TURBINE STANDARD TERMS & CONDITIONS
  • D100A2 :  TURBINE PRODUCT POLICIES

PERFORMANCE CURVES

LINESHAFT

60 HZ

  • C3600 R4 LINESHAFT TURBINE 3600 RPM PUMP CURVES – 60 CYCLE PERFORMANCE
  • C1800 R4 LINESHAFT TURBINE 1800 RPM PUMP CURVES – 60 CYCLE PERFORMANCE
  • C1200 R4 LINESHAFT TURBINE 1200 RPM PUMP CURVES – 60 CYCLE PERFORMANCE
  • C900 R4 LINESHAFT TURBINE 900 RPM PUMP CURVES – 60 CYCLE PERFORMANCE
  • C720 LINESHAFT TURBINE 720 RPM PUMP CURVES – 60 CYCLE PERFORMANCE
  • C600 LINESHAFT TURBINE 600 RPM PUMP CURVES – 60 CYCLE PERFORMANCE
  • C514 LINESHAFT TURBINE 514 RPM PUMP CURVES – 60 CYCLE PERFORMANCE

50 HZ

  • C3000 R4 LINESHAFT TURBINE 3000 RPM PUMP CURVES – 50 CYCLE PERFORMANCE
  • C1500 R4 LINESHAFT TURBINE 1500 RPM PUMP CURVES – 50 CYCLE PERFORMANCE
  • C1000 R4 LINESHAFT TURBINE 1000 RPM PUMP CURVES – 50 CYCLE PERFORMANCE
  • C750 R4 LINESHAFT TURBINE 750 RPM PUMP CURVES – 50 CYCLE PERFORMANCE
  • C600 LINESHAFT TURBINE 600 RPM PUMP CURVES – 50 CYCLE PERFORMANCE
  • C500 LINESHAFT TURBINE 500 RPM PUMP CURVES – 50 CYCLE PERFORMANCE
  • C428 LINESHAFT TURBINE 428 RPM PUMP CURVES – 50 CYCLE PERFORMANCE

SUBMERSIBLE

60 HZ

  • C3600 SUBMERSIBLE TURBINE 3600 RPM PUMP CURVES – 60 CYCLE PERFORMANCE
  • C1800 SUBMERSIBLE TURBINE 1800 RPM PUMP CURVES – 60 CYCLE PERFORMANCE
  • C1200 SUBMERSIBLE TURBINE 1200 RPM PUMP CURVES – 60 CYCLE PERFORMANCE
  • C900 SUBMERSIBLE TURBINE 900 RPM PUMP CURVES – 60 CYCLE PERFORMANCE
  • C720 SUBMERSIBLE TURBINE 720 RPM PUMP CURVES – 60 CYCLE PERFORMANCE

50 HZ

  • C3000 SUBMERSIBLE TURBINE 3000 RPM PUMP CURVES – 50 CYCLE PERFORMANCE
  • C1500 SUBMERSIBLE TURBINE 1500 RPM PUMP CURVES – 50 CYCLE PERFORMANCE
  • C1000 SUBMERSIBLE TURBINE 1000 RPM PUMP CURVES – 50 CYCLE PERFORMANCE
  • C750 SUBMERSIBLE TURBINE 750 RPM PUMP CURVES – 50 CYCLE PERFORMANCE

TURBINE ENGINEERING

  • TOCED :  TURBINE ENGINEERING DATA TABLE OF CONTENTS

TURBINE BOWL ASSEMBLY – ENGINEERING DATA

  • D200A01 :  LINESHAFT TURBINE BOWL ASSEMBLY DATA
  • D200A02 :  TURBINE STRAINERS
  • D200A03/D200A04 : PERFORMANCE CORRECTION FACTORS/BOWL ASSEMBLY PRESSURE LIMITS
  • D200A05 :  MINIMUM SUBMERGENCE REQUIRED FOR VORTEX SUPPRESSION
  • D200A06 :  TURBINE IMPELLER MECHANICAL DATA
  • D200A07 :  LOW NPSH IMPELLERS
  • D200A08 :  TURBINE THRUST DATA
  • D200A09/D200A10 :  CALCULATING BOWL LATERAL REQUIREMENT/CALCULATING MOTOR BEARING LOAD

TURBINE COLUMN ASSEMBLY – ENGINEERING DATA

  • D200B01 :  SHAFT HORSEPOWER LIMITATION 60HZ/50HZ
  • D200B02/D200B03 :  SHAFT WEIGHTS AND SHAFT MECHANICAL FRICTION/ALLOWABLE BEARING SPACING
  • D200B04 :  COLUMN FRICTION LOSS
  • D200B05/D200B06 :  COLUMN AND TUBE ELONGATION/COLUMN LOAD CALCULATIONS
  • D200B07 :  LINESHAFT ELONGATION

TURBINE HEAD ASSEMBLY – ENGINEERING DATA

  • D200C01A : TYPE “DI” DUCTILE IRON DISCHARGE HEAD, 150# ANSI FLANGE
  • D200C01/D200C02 :  TYPE “CA” CAST DISCHARGE HEAD/TYPE “CF” CAST DISCHARGE HEAD
  • D200C03A : TYPE “DL” DUCTILE IRON DISCHARGE HEAD, 150# ANSI FLANGE
  • D200C03 :  TYPE “CL” CAST DISCHARGE HEAD
  • D200C04/D200C05 :  TYPE “FF” FABRICATED DISCHARGE HEAD/TYPE “FL” FABRICATED DISCHARGE HEAD
  • D200C06 /D200C07 : TYPE “FT” FABRICATED DISCHARGE HEAD/TYPE “FU” FABRICATED DISCHARGE HEAD
  • D200C07A : FABRICATED HEADS FLANGE FORCES AND MOMENTS
  • D200C08/D200C09 : DISCHARGE HEAD FRICTION LOSS FOR CAST IRON HEAD/DISCHARGE HEAD FRICTION LOSS FOR FABRICATED STEEL HEAD
  • D200C08A/D200C09 : DISCHARGE HEAD FRICTION LOSS FOR CAST IRON HEAD/DISCHARGE HEAD FRICTION LOSS FOR FABRICATED STEEL HEAD
  • D200C10 : INLET FRICTION LOSS FOR FABRICATED STEEL T HEAD
  • D200C11 :  SUCTION CAN SELECTION DATA
  • D200C12 :  TENSION PLATE ASSEMBLY

TURBINE SUBMERSIBLE – ENGINEERING DATA

  • D200D01 :  SUBMERSIBLE TURBINE PUMPS DATA
  • D200D02 :  SUBMERSIBLE TURBINE PUMPS DATA – CABLE CHART
  • D200D03/D200D04 :  MODEL VAS-SUPPLEMENTAL DATA – COLUMN FRICTION LOSS CHARTS
  • D200D05/D200D06 :  SECTION VIEW CHECK VALVE/CHECK VALVE HEAD LOSS

TECHNICAL DATA

  • D200E01/D200E02 :  TURBINE TERMINOLOGY/DWT TURBINE PUMP SELECTION PROCEDURE
  • D200E03 :  USEFUL FORMULAS
  • D200E04 :  VERTICAL TURBINE PUMPS
  • D200E05 :  CONVERSION TABLES
  • D200E06 :  CONSTANTS FOR PUMP PERFORMANCE AT VARIOUS SPEEDS
  • D200E07/D200E08 :  MEASURING FLOW (ORIFICE METHOD)/MEASURING FLOW (ORIFICE METHOD FOR WATER)
  • D200E09/D200E10:  MEASURING FLOW – FULL PIPE METHOD/WATER LEVEL TESTING
  • D200E11 :  PRE-LUBRICATION RECOMMENDATIONS
  • D200E12 :  STEADY BUSHINGS FOR VERTICAL HOLLOWSHAFT MOTORS

QUOTE SPECIFICATIONS – ENGINEERING DATA

  • D200F01 :  DEEP SET, WATER LUBRICATED SPECIFICATIONS
  • D200F02 :  DEEP SET, OIL LUBRICATED SPECIFICATIONS
  • D200F03 :  SHORT-SET, OPEN LINESHAFT SPECIFICATIONS
  • D200F04 :  SUBMERSIBLE TURBINE PUMPS SPECIFICATIONS
  • D200F05 :  MODEL VAS – SUPPLEMENTAL DATA (VAS SELECTION PROCEDURE)
  • D200F06 : SMVT – VERTICAL MULTISTAGE PUMP SPECIFICATIONS - OBSOLETE
  • D200F07 : CANNED LINESHAFT (VIC) SPECIFICATIONS

OUTLINE DRAWINGS – ENGINEERING DATA

TURBINE CROSS SECTIONAL – ENGINEERING DATA

TURBINE PRE-ENGINEERED  SUBMERSIBLE PUMPS

  • BR5-11TPE :  5″-11″ TEXAS PRE-ENGINEERED SUBMERSIBLE TURBINE PUMPS – 6″ AND LARGER WELLS

TURBINE 316 STAINLESS STEEL SUBMERSIBLE SUBS

  • BR5-11SST : 5″-11″ TEXAS 316 STAINLESS STEEL SUBMERSIBLE TURBINE PUMPS  – 6″ AND LARGER WELLS

TURBINE SMVT

  • SMVT SMVT SPEC SHEET - OBSOLETE

TURBINE REBOWLS

ACCESSORIES

  • TURBINE ACCESSORIES LIST PRICES
  • TURBINE/TURBINE REPAIR PART PRICES

Click here for pricing sheets on ecom.xyleminc.com