Turbine Catalog
GENERAL INFORMATION
- BGTTO : RESIDENTIAL & COMMERCIAL WATER DIRECTORY FOR DISTRIBUTORS
- B-710A : LINESHAFT AND SUBMERSIBLE TURBINE PUMPS
TURBINE TERMS & CONDITIONS
- BGSTCTRBNE R1 : TURBINE STANDARD TERMS & CONDITIONS
- BGD100A2 R1 : TURBINE PRODUCT POLICIES
PERFORMANCE CURVES
3600 RPM
- BGC3600 R1 Lineshaft and Submersible Turbine Pump Curves – 3600 RPM CURVES – 60 CYCLE PERFORMANCE
1800 RPM
- BGC1800 R1 Lineshaft and Submersible Turbine Pump Curves – 1800 RPM CURVES – 60 CYCLE PERFORMANCE
1200 RPM
- BGC1200 R1 Lineshaft and Submersible Turbine Pump Curves – 1200 RPM CURVES – 60 CYCLE PERFORMANCE
900 RPM
- BGC900 R1 Lineshaft and Submersible Turbine Pump Curves – 900 RPM CURVES – 60 CYCLE PERFORMANCE
TURBINE ENGINEERING
- BGTOCED R1 : TURBINE ENGINEERING DATA TABLE OF CONTENTS
TURBINE BOWL ASSEMBLY – ENGINEERING DATA
- BGD200A01 : LINESHAFT TURBINE BOWL ASSEMBLY DATA
- BGD200A02 : TURBINE STRAINERS
- BGD200A03/BGD200A04 : PERFORMANCE CORRECTION FACTORS/BOWL ASSEMBLY PRESSURE LIMITS
- BGD200A05 : MINIMUM SUBMERGENCE REQUIRED FOR VORTEX SUPPRESSION
- BGD200A06 : TURBINE IMPELLER MECHANICAL DATA
- BGD200A07 : LOW NPSH IMPELLERS
- BGD200A08 : TURBINE THRUST DATA
- BGD200A09/BGD200A10 : CALCULATING BOWL LATERAL REQUIREMENT/CALCULATING MOTOR BEARING LOAD
TURBINE COLUMN ASSEMBLY – ENGINEERING DATA
- BGD200B01 : SHAFT HORSEPOWER LIMITATION 60HZ/50HZ
- BGD200B02/BGD200B03 : SHAFT WEIGHTS AND SHAFT MECHANICAL FRICTION/ALLOWABLE BEARING SPACING
- BGD200B04 : COLUMN FRICTION LOSS
- BGD200B05/BGD200B06 : COLUMN AND TUBE ELONGATION/COLUMN LOAD CALCULATIONS
- BGD200B07 : LINESHAFT ELONGATION
TURBINE HEAD ASSEMBLY – ENGINEERING DATA
- BGD200C01A : TYPE “DI” DUCTILE IRON DISCHARGE HEAD, 150# ANSI FLANGE
- BGD200C01/BGD200C02 : TYPE “CA” CAST DISCHARGE HEAD/TYPE “CF” CAST DISCHARGE HEAD
- BGD200C03A : TYPE “DL” DUCTILE IRON DISCHARGE HEAD, 150# ANSI FLANGE
- BGD200C03 : TYPE “CL” CAST DISCHARGE HEAD
- BGD200C04/BGD200C05 : TYPE “FF” FABRICATED DISCHARGE HEAD/TYPE “FL” FABRICATED DISCHARGE HEAD
- BGD200C06 /BGD200C07 : TYPE “FT” FABRICATED DISCHARGE HEAD/TYPE “FU” FABRICATED DISCHARGE HEAD
- BGD200C07A : FABRICATED HEADS FLANGE FORCES AND MOMENTS
- BGD200C08/BGD200C09 : DISCHARGE HEAD FRICTION LOSS FOR CAST IRON HEAD/DISCHARGE HEAD FRICTION LOSS FOR FABRICATED STEEL HEAD
- BGD200C08A/BGD200C09 : DISCHARGE HEAD FRICTION LOSS FOR CAST IRON HEAD/DISCHARGE HEAD FRICTION LOSS FOR FABRICATED STEEL HEAD
- BGD200C10 : INLET FRICTION LOSS FOR FABRICATED STEEL T HEAD
- BGD200C11 : SUCTION CAN SELECTION DATA
- BGD200C12 : TENSION PLATE ASSEMBLY
TURBINE SUBMERSIBLE – ENGINEERING DATA
- BGD200D01 : SUBMERSIBLE TURBINE PUMPS DATA
- BGD200D02 : SUBMERSIBLE TURBINE PUMPS DATA – CABLE CHART
- BGD200D03/BGD200D04 : MODEL VAS-SUPPLEMENTAL DATA – COLUMN FRICTION LOSS CHARTS
- BGD200D05/BGD200D06 : SECTION VIEW CHECK VALVE/CHECK VALVE HEAD LOSS
- BCPFMSERIE : CENTRIPRO FM-SERIES, THREE PHASE, 6″ MOTORS
TECHNICAL DATA
- BGD200E01/BGD200E02 : TURBINE TERMINOLOGY/DWT TURBINE PUMP SELECTION PROCEDURE
- BGD200E03 : USEFUL FORMULAS
- BGD200E04 : VERTICAL TURBINE PUMPS
- BGD200E05 : CONVERSION TABLES
- BGD200E06 : CONSTANTS FOR PUMP PERFORMANCE AT VARIOUS SPEEDS
- BGD200E07/BGD200E08 : MEASURING FLOW (ORIFICE METHOD)/MEASURING FLOW (ORIFICE METHOD FOR WATER)
- BGD200E09/BGD200E10: MEASURING FLOW – FULL PIPE METHOD/WATER LEVEL TESTING
- BGD200E11 : PRE-LUBRICATION RECOMMENDATIONS
- BGD200E12 : STEADY BUSHINGS FOR VERTICAL HOLLOWSHAFT MOTORS
OUTLINE DRAWINGS – ENGINEERING DATA
- BGD200G01A : OUTLINE TYPE “DWT-DITM”/OUTLINE TYPE “VIT-DITM”
- BGD200G01/BGD200G02 : OUTLINE TYPE “DWT-CATM”/OUTLINE TYPE “VIT-CATM”
- BGD200G03/BGD200G04: OUTLINE TYPE “VIT-CFTM”/OUTLINE TYPE “VIT-CFFM”
- BGD200G06A : OUTLINE TYPE “VIC-DLFM”
- BGD200G05/BGD200G06 : OUTLINE TYPE “VIT-FFFM”/OUTLINE TYPE “VIC-CLFM”
- BGD200G07/BGD200G08 : OUTLINE TYPE “VIC-FLFM”/OUTLINE TYPE “VIC-FLCM”
- BGD200G09/BGD200G10 : OUTLINE TYPE “VIC-FTCM”/OUTLINE TYPE “VIC-FTFM”
- BGD200G11 : OUTLINE TYPE “VIT-FUFM”
- BGD200G12/BGD200G13 : OUTLINE TYPE “VIS”/OUTLINE TYPE “VIS-WF”
TURBINE CROSS SECTIONAL – ENGINEERING DATA
- BGD200H01A : SECTIONAL TYPE “VIT-DITM”/ SECTIONAL TYPE “DWT-DITM”
- BGD200H01/BGD200H02 : SECTIONAL TYPE “VIT-CATM”/ SECTIONAL TYPE “DWT-CATM”
- BGD200H03A : SECTIONAL TYPE “DWT-DITM”
- BGD200H03/BGD200H04: SECTIONAL TYPE “DWT-CATM”/ SECTIONAL TYPE “VIT-CFFM”
- BGD200H05/BGD200H06 : SECTIONAL TYPE “VIT-FFFM”/ SECTIONAL TYPE “VIT-FFFM”
- BGD200H07A : SECTIONAL TYPE “VIC-DLFM”
- BGD200H07/BGD200H08 : SECTIONAL TYPE “VIC-CLFM”/ SECTIONAL TYPE “VIT-CLFM”
- BGD200H09/BGD200H10 : SECTIONAL TYPE “VIT-FLFM”/ SECTIONAL TYPE “VIT-FLFM”
- BGD200H11/BGD200H12: SECTIONAL TYPE “VIT-FTFM”/ SECTIONAL TYPE “VIC-FTFM”
- BGD200H13 : SECTIONAL TYPE “VIT-FUFM”
- BGD200H14/BGD200H15 : SECTION VIEW SUBMERSIBLE / SECTIONAL TYPE “VIS-“
- BGD200H16 : SECTIONAL TYPE “VIS-WF”
TURBINE REBOWLS
- BGDROF : RETROFIT ORDER FORM
- BGOTURBPG1 : REBOWL FLANGED ORDER FORM
- BGOTURBPG3 R1 : REBOWL THREADED ORDER FORM
- BGTURBSTAND : TURBINE STANDARDS SHEET
ACCESSORIES
- TURBINE ACCESSORIES LIST PRICES
- TURBINE/TURBINE REPAIR PART PRICES
Click here for pricing sheets on ecom.xyleminc.com